Design, Development and Study of Optimal Parameters of a Micro Wire Electrical Discharge Machining (WEDM) Device

Design, Development and Study of Optimal Parameters of a Micro Wire Electrical Discharge Machining (WEDM) Device

Master's

Saved in:

書目詳細資料
主要作者:	SADIQ MOHAMMAD ALAM
其他作者:	MECHANICAL ENGINEERING
格式:	Theses and Dissertations
語言:	English
出版:	2010
主題:	WEDM, EDM, electro discharge machining, micro machining, micro fabrication, parameter study
在線閱讀:	http://scholarbank.nus.edu.sg/handle/10635/15727
標簽:	添加標簽沒有標簽, 成為第一個標記此記錄!
機構:	National University of Singapore
語言:	English

相似書籍

A study on the machining of high-aspect ratio micro-structures using micro-EDM
由: Lim, H.S., et al.
出版: (2014)

Micro-Electro Discharge Machining (μEDM)
由: Jahan, M.P., et al.
出版: (2014)

Tool-based micro-machining
由: Asad, A.B.M.A., et al.
出版: (2014)

Performance analysis of EDM electrode fabricated by localized electrochemical deposition for micro-machining of stainless steel
由: Habib, M.A., et al.
出版: (2014)

Enhanced surface integrity and dimensional accuracy by simultaneous micro-ED/EC milling
由: Nguyen, M.D., et al.
出版: (2014)

A review on the conventional and micro-electrodischarge machining of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Modeling and Simulation of Crater Formation and Wire Vibration in Micro WEDM
由: FENG XIAOBING
出版: (2014)

MICRO-EDM-BASED MULTI-PROCESS MACHINING OF TUNGSTEN CARBIDE
由: MUHAMMAD PERVEJ JAHAN
出版: (2010)

Experimental investigations into the influence of major operating parameters during micro-electro discharge drilling of cemented carbide
由: Jahan, M.P., et al.
出版: (2014)

Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide
由: Lee, S.H., et al.
出版: (2014)

Development of localized electrochemical deposition process for the fabrication of on-machine micro-EDM electrode
由: MOHAMMAD AHSAN HABIB
出版: (2010)

Simultaneous micro-EDM and micro-ECM in low-resistivity deionized water
由: Nguyen, M.D., et al.
出版: (2014)

Fabrication of different geometry cutting tools and their effect on the vertical micro-grinding of BK7 glass
由: Perveen, A., et al.
出版: (2014)

Accuracy improvement in nanographite powder-suspended dielectric fluid for micro-electrical discharge machining processes
由: Prihandana, G.S., et al.
出版: (2014)

In-situ machining of varied-shaped and arrays of microelectrodes using reverse micro-electrodischarge machining
由: Jahan, M.P., et al.
出版: (2014)

A STUDY OF THE OPTIMUM PARAMETERS IN EDM MACHINING OF TUNGSTEN CARBIDE MATERIAL
由: KHIN MOE AYE
出版: (2020)

Tool-based nanofinishing and micromachining
由: Rahman, M., et al.
出版: (2014)

Simultaneous Micro-EDM and Micro-ECM in Low-resistivity Deionized Water
由: NGUYEN MINH DANG
出版: (2013)

Investigation of micro-EDM material removal characteristics using single RC-pulse discharges
由: Wong, Y.S., et al.
出版: (2014)

Workpiece vibration aided nano-graphite powder suspended dielectric fluid in micro-electrical discharge machining (μ-EDM) processes
由: Prihandana, G.S., et al.
出版: (2014)

Integrated hybrid micro/nano-machining
由: Rahman, M., et al.
出版: (2014)

An experimental investigation of single and multi-tool micro-EDM
由: MASHEED AHMAD
出版: (2010)

An Experimental Investigation on Surface Characteristics of Tool Steel using Powder Mixed Micro-EDM
由: MOHAMMED MUNTAKIM ANWAR
出版: (2010)

An experimental investigation into the micro-electrodischarge machining behavior of p-type silicon
由: Jahan, M.P., et al.
出版: (2014)

A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator
由: Jahan, M.P., et al.
出版: (2014)

Study of workpiece vibration in powder-suspended dielectric fluid in micro-EDM processes
由: Prihandana, G.S., et al.
出版: (2014)

Nanofinishing of hard materials using micro-electrodischarge machining
由: Jahan, M.P., et al.
出版: (2014)

A study of abrasive jet micro-grooving of quartz crystals
由: Moridi, A., et al.
出版: (2014)

Revealing the WEDM process parameters for the machining of pure and heat-treated titanium (Ti-6Al-4V) alloy
由: Gupta, Nitin Kumar, et al.
出版: (2022)

Transitions of micro-EDM/SEDCM/micro-ECM milling in low-resistivity deionized water
由: Nguyen, M.D., et al.
出版: (2014)

Formation of electrical discharge machining electrode via laser cladding
由: Tang, Y., et al.
出版: (2014)

Effect of TiC in copper-tungsten electrodes on EDM performance
由: Li, L., et al.
出版: (2014)

Fabrication of EDM electrodes by localized electrochemical deposition
由: Habib, M.A., et al.
出版: (2014)

Fabrication of micro-optical components in polymer using proton beam micro-machining and modification
由: Bettiol, A.A., et al.
出版: (2014)

On-machine fabrication of high-aspect-ratio micro-electrodes and application in vibration-assisted micro-electrodischarge drilling of tungsten carbide
由: Jahan, M.P., et al.
出版: (2014)

Micro-mould fabrication for a micro-gear via vacuum casting
由: Tang, Y., et al.
出版: (2013)

Fabrication of 3D submicron to micro textured surfaces using backside patterned texturing (BPT)
由: Ahmed, Syed Adnan, et al.
出版: (2017)

Micro milling of pure copper
由: Rahman, M., et al.
出版: (2014)

Cutting force analysis of on-machine fabricated PCD tool during glass micro-grinding
由: Perveen, A., et al.
出版: (2014)

Modeling of radial gap formed by material dissolution in simultaneous micro-EDM and micro-ECM drilling using deionized water
由: Nguyen, M.D., et al.
出版: (2014)